background image

Pinch Valve Assembly

1

Part 768670A

.

2005 Nordson Corporation

Pinch Valve Assembly

Safety

WARNING:

Allow only qualified personnel to perform the following tasks.

Observe and follow the safety instructions in this document and all other

related documentation.

Read and follow these safety instructions. Task- and equipment-specific

warnings, cautions, and instructions are included in equipment

documentation where appropriate.

Make sure all equipment documentation, including these instructions, is

accessible to all persons operating or servicing equipment.

Qualified Personnel

Equipment owners are responsible for making sure that Nordson equipment

is installed, operated, and serviced by qualified personnel. Qualified

personnel are those employees or contractors who are trained to safely

perform their assigned tasks. They are familiar with all relevant safety rules

and regulations and are physically capable of performing their assigned

tasks.

Intended Use

Use of Nordson equipment in ways other than those described in the

documentation supplied with the equipment may result in injury to persons

or damage to property.

Some examples of unintended use of equipment include

:

using incompatible materials

:

making unauthorized modifications

:

removing or bypassing safety guards or interlocks

:

using incompatible or damaged parts

:

using unapproved auxiliary equipment

:

operating equipment in excess of maximum ratings

Содержание 768670A




























Отзывы: