Nordmann Engineering Omega Pro 10, Руководство по установке

Страница: 48 / 64

48
ACCESSORY BOARD
REMOTE BOARD
BMS
LinkUp
SAB
3V
CR2032
BAT
SD
J7
J4
J8
J11
(USB)
(RJ45)
GND
+
–
GND
+
–
GND
+
–
24V
GND
MAINS SUPPLY
L N SC1SC2PEPE
MODULE B 24VDC
LEVEL
UNIT
POWER
BOARD
DRN1 J2 INLET J1
PWR
SUPPLY
BLOWER LIMIT ENABLE CONTROL
VOUT
X8 X9 X12 X11 X10 X7 X1
IN GND IN GND 24V IN 24V IN 24V GND
RS485
RS485
PWRIC
CONT- ACTOR
HEAT GR.
2+3
JP2 (24V) JP1 (10V)
PUMP
AC
SWITCH
GND
D–
D+
GND
D–
D+
24V
GND
DRN2 J3
J8
F1
SW1
F2
H1
Error
1 2 3
Service
4 5 6
Steam
7 8
Unit On
9 10
H2
Hyg. Valve A FAN B
1 2 3
Hyg. Valve B
4 5 6 7 8
FAN A
9 10
L1 L2 L3
L1 L2 L3 PE
K1
THV
Q3
F3
200-600 V/3~/50..60 Hz
230 V/1~/50..60 Hz
L1 N PE
Q3
F3
B3
B2
B1
L1 N PE
F4
Q4
230 V/1~/50..60 Hz
K2
J3 J1
230V
B4
L1 L2 L3
Y1 Y2 B5
M
L1 N PE
140Ω...10kΩ
A2
On/Off
A3
GND IN VOUT
IN VOUT
JP1
JP2
A1 A4
Y
+ –
Z
+ –
140Ω...10kΩ
A5
GND IN VOUT
JP1
Z
400-415 V/3~N/50..60 Hz
F3
Q3
400-500 V/3~/50..60 Hz
F3
Q3
L2 L3 PE L1
L2 L3 PE N L1
L2 L3 L1
N PE L1
L2 L3 L1 N PE L1
Control compartment
Driver board
Option TR (3Ph)
Option CVI (3Ph+N)
5.7.2 Wiring diagram Nordmann Omega Pro 5...40 - Single units "S" and "M"
Fig. 20: Wiring diagram Nordmann Omega Pro - Single units "S" and "M" (5...40 kg/h)
A1 Continuous humidity controller (active) or humidity sensor
A2 Ohmic humidity controller (passive),
set jumper JP1 and remove jumper JP2
A3 On/Off humidity controller,
set jumper JP2 and remove jumper JP1
A4 Limiter signal
A5 Ohmic limiter controller, set jumper JP1 and remove jumper JP2
B1 Ventilation interlock
B2 Airflow monitor
B3 Safety humidistat
B4 External enable contact (potential-free)
B5 External drain contact (potential-free)
F1 Internal fuse 24V supply (1 A, slow acting)
F2 Internal fuse 230V supply (6.3 A, slow acting)
F3 External fuse heating voltage supply
(see table in chapter 5.7.5 )
F4 External fuse control voltage (max. 10 A, slow acting)
J1 Jumper wire (do not remove!)
J3 Jumper wire, if no monitoring devices are connected to SC1 and SC2
J4 Jumper for activating the terminating resistor for Modbus network
(Jumper must be connected, if Nordmann Omega Pro is the last unit in
the Modbus network)
J7 Jumper for activating Modbus or BACnet MSTP communication via
RS485 interface (J6). If jumper is not in place no communication will
take place through the RS485 interface.
H1 Remote operating and fault indication (option)
H2 Accessory board (option) for the control of an external fan of the AHU
as well as the optional external valve for the water supply line flushing
K1 Mains contactor (heating voltage)
K2 External safety circuit (safety humidistat, airflow monitor, etc.)
M Motor fan unit
Q3 External main switch heating voltage supply
Q4 External main switch control voltage supply
SW1 Rotary switch Module identification (must be left on position "0")
THV Terminal Heating voltage supply (option)
Y1 Drain cooling valve (option)
Y2 Total drain valve (option)
6.3 A,
slow acting
6.3 A, slow acting
Ethernet (RJ45) IP
network / BMS BACnet IP
RS 485 BACnet MSTP
Control board