nord 6052902/0213 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 128

background image

Industrial gear units – Manual with installation instructions

56

B 1050 en-3921

Legend

1:

Gear unit intake connection

2:

Pump/cooling system intake
connection

3:

Cooling system pressure
connection

4:

Gear unit pressure connection

5:

PT100 temperature monitoring
(optional/recommended)

6:

Cooling water connection

Figure 27: Industrial gear unit with CS1-X and CS2-X cooling systems

Legend

1:

Intake connection

2:

Pump

3:

Heat exchanger

4:

Cooling system pressure connection

5:

Temperature monitor (PT100)

6:

Cooling water connection

Figure 28: Hydraulic plan of industrial gear units with CS1-X and CS2-X cooling systems

3.20 Installing a fan (Option: FAN-A, FAN-R)

The fan wheel of a radial and axial fan is arranged on the high-speed shaft of the gear unit and
protected against accidental contact by a fan cover. The fan takes in air through the protective grill of
the fan cover. The lateral air baffles of the fan cover guide the air past the gear unit housing. Through
this, the air dissipates a specific amount of the housing heat.

An electrical external fan, which is driven by an external three-phase motor, is available as a special
option. For the correct installation and the electrical connection, refer to the manufacturer’s manual.

«
...
54
55
56
57
58
...
»

Содержание 6052902/0213

































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6052902/0213

Parilla Norswift 60cc

Бренд: IAME Страницы: 9

Parilla Norswift 60cc

Бренд: IAME Страницы: 35

Бренд: Yanmar Страницы: 224

Бренд: Stihl Страницы: 40

Бренд: Ecofly Страницы: 20

Бренд: Evolution Technologies Страницы: 12

Бренд: YASKAWA Страницы: 447

Бренд: Volvo Страницы: 179

Бренд: Volvo Penta Страницы: 41

Бренд: BAFANG Страницы: 6

Бренд: Lycoming Страницы: 90

Бренд: Robin America Страницы: 36

Бренд: Honda Страницы: 60

Бренд: Honda Страницы: 149

Бренд: Motion Страницы: 52

Бренд: Motion Страницы: 64

Бренд: STEYR Страницы: 118

Бренд: LinMot Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды