Nokta MAKRO Racer 2 страница 2 Скачать руководство пользователя

Страница: 2 / 32

READ CAREFULLY BEFORE OPERATING THE DEVICE!

LEGAL DISCLAIMERS

Comply with the laws and regulations in force within the area while using the device.

Do not use the device in protected or archeological sites and military zones. Notify

any historical and cultural artifacts you find to the concerned authorities.

WARNINGS

RACER 2

is a state-of-the-art electronic device. Do not assemble or operate the

device before reading the user manual.

Do not keep the device and search coil under extremely low and high temperatures

for extended periods. (Storage Temperature: - 20°C to 60°C / - 4°F to 140°F)

Do not immerse the device and its accessories (except for the search coil) in water or

keep them in excessively humid environments.

Protect the device against impacts that may occur during shipping in particular.

RACER 2

may only be disassembled and repaired by authorized service centers.

Disassembling the device for any reason voids the warranty.

Содержание Racer 2

































Результаты поиска

Содержание Racer 2

Отзывы:

Похожие инструкции для Racer 2

Бренды по названию

Популярные бренды

Nokta MAKRO Racer 2, Руководство пользователя

Результаты поиска

Содержание Racer 2

Отзывы:

Похожие инструкции для Racer 2

Бренды по названию

Популярные бренды