background image

Turning On/Off the Device

To turn on the device, press and hold the On/Off button        until the 

bar starts filling up. To turn off the device, press and hold the button 

until the display light turns off.

Sensitivity

This is the depth setting of the device. It is also used to 

eliminate the ambient electromagnetic signals from the 

surrounding environment and noise signals transmitted 

from ground.  

Sensitivity setting consists of 8 levels and is pre-defined for each 

mode. Each mode starts with its default sensitivity setting and it can 

be manually modified when necessary.

Note :

 If the ground is highly mineralized causing the device to 

overload, decrease the Sensitivity until the overload warning icon  

        disappears from the screen.

Pinpoint

Pinpoint is to find the center or the exact location of a detected target.

To perform pinpoint :

1- After a target is detected, move the search coil aside where there 

is no target response and push the Pinpoint button       .

2-  Keep the button pressed down and bring the search coil closer to 

the target slowly and parallel to the ground.

3- Signal sound becomes stronger and changes in pitch while getting 

closer to the target center. In addition, the bar on screen will rise or 

fall based on signal strength.

4- Mark the position which provides the loudest sound using a tool or 

your foot.

5- Repeat the above procedure by changing your direction 90°. 

Actions to be performed from a couple of different directions will 

narrow the target area and provide you with the most exact details 

of the target location.

Frequency Shift

It is used to eliminate the electromagnetic interference that the device 

receives from another detector which operates in the same frequency range 

nearby or from the surroundings. If too much noise is received when the 

search coil is lifted in the air, this may be caused by the local electromagnetic 

signals or excessive sensitivity settings.

To shift the frequency, press and hold the M button         for 3 seconds while 

the device is on. The frame around the search modes icon will start blinking. 

Change the frequency using the sensi/- buttons.

Note :

 If no button is pressed for 5 seconds, the screen will time out and the 

device will revert back to the main screen.  

Frequency shift will be reflected on the left side of the bar. The left side of the 

bar will start filling up / falling each time you press the sensi/- 

buttons. Frequency shift consists of 10 steps and 5 is the central frequency. 

IMPORTANT!

 At each power up, the frequency shift setting will start at the 

central frequency of 5.

Search Modes

There are 2 search modes: All Metal and Discrimination. Press the M 

button         to select the mode.

All Metal Mode

In this mode, the device does not provide audio tone discrimination 

and gives the same audio tone for all types of targets. 

Discrimination Mode

In this mode, the device does NOT provide any audio tone for ferrous 

metals and it provides a high tone for non-ferrous metals.

In both search modes:

When the device detects a ferrous metal, the left side of 

the bar fills up in proportion to the strength of the target 

signal.

When the device detects a non-ferrous metal, the right 

side of the bar fills up in proportion to the strength of the 

target signal.

1) On / Off Button
2) Search Mode Button
3) Search Modes
4) Pinpoint Button
5) Volume Buttons
6) Sensitivity Buttons
7) Signal Strength Bar
8) Warning Icons
9) Battery Icon

10) Wireless Connection Icon

Control Display

Illumination LEDs

It is the flashlight used for lighting the area you are scanning while detecting 

at night or in dark locations. To activate the LEDs, while the detector is on, 

press the pinpoint and volume minus (-) buttons at the same time. Repeat 

the same to turn them off. LEDs do not operate when the device is off. It is 

recommended to turn them on only when necessary since they consume 

extra battery power.

Volume

Press the + or - button to adjust the volume.

QUICK GUIDE

2

1

7

8

9

10

4 5

6

3

Отзывы: