manualshive.com logo in svg

Nokia NPM-2NX, Руководство по устранению неисправностей

Поделиться
Скачать
Nokia NPM-2NX Скачать руководство пользователя страница 33

CCS Technical Documentation

Troubleshooting

NPM-2NX

Issue 1 07/02

ã

Nokia Corporation

Page 33

power level, for example 10. Set channel to 380 and press "Write Init".

4) Connect oscilloscope probe to one of the RX I/Q test points on PWB (all four testpoints 
J808, J809, J818 and J819 are located behind display)

5) Check that there is a clean signal in each test points.

6) Decrease signal level slowly down to -115 dBm and make sure that AGC keeps signal 
in visible (This can be noticed by looking at the RX I/Q voltage during signal level 
change).

7) Measure and record the frequency and peak-to-peak voltage of RX I/Q signal from 
each test points. Voltage should be around 100 mVp-p and frequency 6.5 kHz +/- 3 kHz.

TDMA800

Since there is same physical signal path for both analog (AMPS) and digital mode (TDMA) 
in lower band there is no need for additional troubleshooting in digital mode. If digital 
mode in lower band is not working properly start analog mode troubleshooting.

TDMA1900

Only path from external RF connector to IF needs to be checked if AMPS/TDMA800 RX 
chain is OK. After down conversion (from RF to 134.04 MHz IF) both lower and upper 
band use same signal path.

Содержание NPM-2NX



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды