Nokia 7360 Intelligent Services Access Manager FX Series Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 626

Nokia 7360 Intelligent Services Access Manager FX Series Скачать руководство пользователя страница 301

FD 100/320Gbps NT and FX NT IHub Services Guide

Virtual Private LAN Service

Issue: 13

3HH-11985-AAAA-TQZZA

301

5.16.4.8

ccm-ltm-priority

Table 215

ccm-ltm-priority command

5.16.4.9

low-priority-defect

Table 216

low-priority-defect command

Item

Description

Syntax

ccm-ltm-priority

priority

no ccm-ltm-priority

Context

configure>service>vpls>sap>eth-cfm>mep
configure>service>vpls>mesh-sdp>eth-cfm>mep
configure>service>vpls>spoke-sdp>eth-cfm>mep
configure>eth-ring>path>eth-cfm>mep

Description

This command enables configuration of priority for CCM and LTM messages

Default

7

Parameters

priority

- Priority of the CCM/LTM Message

Value: 0...7

Item

Description

Syntax

low-priority-defect

{

allDef

|

macRemErrXcon

|

remErrXcon

|

errXcon

|

xcon

|

noXcon

}

Context

configure>service>vpls>sap>eth-cfm>mep
configure>service>vpls>mesh-sdp>eth-cfm>mep
configure>service>vpls>spoke-sdp>eth-cfm>mep
configure>eth-ring>path>eth-cfm>mep

Description

This command specifies the lowest priority defect that is allowed to generate a fault alarm.

Default

macRemErrXcon

Parameters

allDef

- DefRDICCM, DefMACstatus, DefRemoteCCM, DefErrorCCM and DefXconCCM

macRemErrXcon

- DefMACstatus, DefRemoteCCM, DefErrorCCM and DefXconCCM

remErrXcon

- DefRemoteCCM, DefErrorCCM and DefXconCCM

errXcon

- DefErrorCCM and DefXconCCM

xcon

- DefXconCCM

noXcon

- No defects DefXcon or lower are to be reported

«
...
299
300
301
302
303
...
»

Содержание 7360 Intelligent Services Access Manager FX Series



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов