manualshive.com logo in svg

Nokia 7360 Intelligent Services Access Manager FX Series, Руководство пользователя, Страница: 283 / 626

Поделиться
Скачать
Nokia 7360 Intelligent Services Access Manager FX Series Скачать руководство пользователя страница 283

FD 100/320Gbps NT and FX NT IHub Services Guide

Virtual Private LAN Service

Issue: 13

3HH-11985-AAAA-TQZZA

283

 

5.16.2.56

split-horizon-group

Table 181

split-horizon-group command

5.16.2.57

vc-type

Table 182

vc-type command

Item

Description

Syntax

[no] split-horizon-group

 

[group-name]

Context

config>service>pw-template

Description

This command creates a new split horizon group (SHG).
Auto-discovered SDP will forward the traffic between the SDPs by default. If mesh kind of 
behavior is required, split horizon group needs to be configured.
If split horizon group is configured, auto SDP will not forward the traffic between them.
The 

no

 form of the command removes the group name from the configuration.

Parameters

group-name

 — Specifies the name of the split horizon group to which the SDP belongs.

Values

A split horizon group is by default not created in a pw-template.

Item

Description

Syntax

vc-type {ether | vlan}

Context

config>service>pw-template

Description

This command overrides the default VC type signaled for the binding to the far end SDP. The 
VC type is a 15 bit-quantity containing a value which represents the type of VC. The actual 
signaling of the VC type depends on the signaling parameter defined for the SDP. If signaling 
is disabled, the 

vctype

 command can still be used to define the dot1q value expected by the 

far-end provider equipment.
A change of the bindings VC type causes the binding to signal the new VC type to the far end 
when signaling is enabled.
VC types are derived according to IETF 

draft-martini-l2circuit-trans-mpls

.

•

The VC type value for Ethernet is 0x0005.

•

The VC type value for an Ethernet VLAN 0x0004.

Parameters

ether

 — Defines the VC type as Ethernet. The 

ethernet

 and 

vlan

 keywords are mutually 

exclusive. When the VC type is not defined, the default is Ethernet for spoke SDP bindings. 
Defining Ethernet is the same as executing 

no vc-type

 and restores the default VC type for 

the spoke SDP binding (hex 5).

vlan

 — Defines the VC type as VLAN. The 

ethernet

 and 

vlan

 keywords are mutually 

exclusive. When the VC type is not defined, the default is Ethernet for spoke SDP bindings.

Содержание 7360 Intelligent Services Access Manager FX Series



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов