Nixie Clock ITS1A Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 29

background image

23

ITS1A CLOCK

Motion Sensor

Another option: The software includes support for a motion sensor. It should be powered by 5V and
have a 3V3 signal output. A value of 3V3 should indicate that motion has been detected.

Attach the signal output to the pin (or hole) marked RX on the programming header at the back. Attach
0V/ground to any convenient GND point on the board. Likewise, 5V to any conv5V point
on the board.

Personally I find it useful to connect an LED across signal and 0V, so I can see if the sensor is actually

working. If you do, don’t forget a current

-limiting resistor!

The clock will work fine without a motion sensor attached

–

it is only used if you connect one.

«
...
21
22
23
24
25
...
»

Содержание ITS1A






























Отзывы:

Нет отзывов

Похожие инструкции для ITS1A

Бренд: Oliver Hemming Страницы: 9

Бренд: BALANCE TIME Страницы: 2

Бренд: La Crosse Technology Страницы: 12

Nixie Clock V600

Бренд: Nocrotec Страницы: 16

Бренд: MOB Страницы: 14

Бренд: Braun Страницы: 2

Бренд: Jensen Страницы: 22

L'Epee 1839 Starfleet Explorer

Бренд: MB&F Страницы: 12

Бренд: GPX Страницы: 2

Бренд: Transonic Страницы: 6

Бренд: Marlo Incorporated Страницы: 28

Бренд: Tesco Страницы: 12

Бренд: TFA Страницы: 20

Бренд: iHome Страницы: 12

Бренд: iHome Страницы: 16

Бренд: RCA Страницы: 9

Dream Machine ICF-C211L

Бренд: Sony Страницы: 5

Dream Machine ICF-C414

Бренд: Sony Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды