Niveo NGSME48T4H Скачать руководство пользователя страница 38

Страница: 38 / 338

Chapter

3: Web Management

Configuration - Ports

NGSME48T4H Switch User Manual | 38

3.1.3. Configuration - Ports

This page displays current port configurations. Ports can also be configured here.

The port settings relate to the currently selected stack unit, as reflected by the page header.

Port

This is the logical port number for this row.

Link

The current link state is displayed graphically. Green indicates the link is up and red that it is

down.

Current Link Speed

The current link speed of the port.

Configured Link Speed

Selects any available link speed for the given switch port. Only speeds supported by the

specific port is shown. Possible speeds are:



Disabled

- Disables the switch port operation.



Auto

- Cu port auto negotiating speed with the link partner and selects the highest

speed that is compatible with the link partner.



10Mbps HDX

- Forces the cu port in 10Mbps half duplex mode.



10Mbps FDX

- Forces the cu port in 10Mbps full duplex mode.



100Mbps HDX

- Forces the cu port in 100Mbps half duplex mode.



100Mbps FDX

- Forces the cu port in 100Mbps full duplex mode.



1Gbps FDX

- Forces the cu port in 1Gbps full duplex mode.

Flow Control

When Auto Speed is selected on a port, this section indicates the flow control capability that is

advertised to the link partner.

When a fixed-speed setting is selected, that is what is used. The Current Rx column indicates

whether pause frames on the port are obeyed, and the Current Tx column indicates whether

pause frames on the port are transmitted. The Rx and Tx settings are determined by the

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды