Niveo NGSME48T4H Скачать руководство пользователя страница 310

Страница: 310 / 338

Chapter

3: Web Management

Diagnostics - VeriPHY

PoE Switch User Manual | 310

3.3.3. Diagnostics - VeriPHY

This page is used for running the VeriPHY Cable Diagnostics for 10/100 and 1G copper ports.

Press

the “Start” button to run the diagnostics. This will take approximately 5 seconds. If all

ports are selected, this can take approximately 15 seconds. When completed, the page

refreshes automatically, and you can view the cable diagnostics results in the cable status

table. Note that VeriPHY is only accurate for cables of length 7 - 140 meters.

10 and 100 Mbps ports will be linked down while running VeriPHY. Therefore, running

VeriPHY on a 10 or 100 Mbps management port will cause the switch to stop responding until

VeriPHY is complete.

The ports belong to the currently selected stack unit, as reflected by the page header.

Port

The port where you are requesting VeriPHY Cable Diagnostics.

Cable Status

Port:



Port number

Pair:

The status of the cable pair.



OK - Correctly terminated pair



Open - Open pair



Short - Shorted pair



Short A - Cross-pair short to pair A



Short B - Cross-pair short to pair B



Short C - Cross-pair short to pair C



Short D - Cross-pair short to pair D



Cross A - Abnormal cross-pair coupling with pair A



Cross B - Abnormal cross-pair coupling with pair B



Cross C - Abnormal cross-pair coupling with pair C



Cross D - Abnormal cross-pair coupling with pair D

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды