Niveo NGSME48T4H Скачать руководство пользователя страница 305

Страница: 305 / 338

Chapter

3: Web Management

Monitor - sFlow

PoE Switch User Manual | 305

3.2.15. Monitor - sFlow

This page shows receiver and per-port sFlow statistics.

Receiver Statistics

Owner

This field shows the current owner of the sFlow configuration. It assumes one of three values

as follows:



If sFlow is currently unconfigured/unclaimed, Owner contains <none>.



If sFlow is currently configured through Web or CLI, Owner contains <Configured

through local management>.



If sFlow is currently configured through SNMP, Owner contains a string identifying the

sFlow receiver.

IP Address/Hostname

The IP address or hostname of the sFlow receiver.

Timeout

The number of seconds remaining before sampling stops and the current sFlow owner is

released.

Tx Successes

The number of UDP datagrams successfully sent to the sFlow receiver.

Tx Errors

The number of UDP datagrams that has failed transmission.

The most common source of errors is invalid sFlow receiver IP/hostname configuration. To

diagnose, paste the receiver's IP address/hostname into the Ping Web page (Diagnostics

→

Ping/Ping6).

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды