Niveo NGSME48T4H Скачать руководство пользователя страница 30

Страница: 30 / 338

Chapter

3: Web Management

System - NTP

NGSME48T4H Switch User Manual | 30

3.1.1.3. System - NTP

NTP stands for Network Time Protocol, which allows switch to perform clock synchronization

with the NTP server.

Mode

You can enable or disable NTP function on this switch:



Enabled:

Enable NTP client mode.



Disabled:

Disable NTP client mode.

Server 1~5

Provide the IPv4 or IPv6 address of a NTP server. IPv6 address is in 128-bit records

represented as eight fields of up to four hexadecimal digits with a colon separating each field

(:). For example, 'fe80::215:c5ff:fe03:4dc7'. The symbol '::' is a special syntax that can be

used as a shorthand way of representing multiple 16-bit groups of contiguous zeros; but it

can appear only once. It can also represent a legally valid IPv4 address. For example,

'::192.1.2.34'.

Also, you can just input NTP server’s URL here as well.

Buttons



Save:

Click to save changes.



Reset:

Click to undo any changes made locally and revert to previously saved values.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды