Niveo NGSME48T4H Скачать руководство пользователя страница 213

Страница: 213 / 338

Chapter

3: Web Management

System - Log

PoE Switch User Manual | 213

3.2.1.4. System - Log

The switch system log information is provided here.

The ID (>= 1) of the system log entry.

Level

The level of the system log entry. The following level types are supported:



Info:

Information level of the system log.



Warning:

Warning level of the system log.



Error:

Error level of the system log.



All:

All levels.

Time

The time of the system log entry.

Message

The message of the system log entry.

Buttons



Auto-refresh:

Check this box to refresh the page automatically. Automatic refresh

occurs every 3 seconds.



Refresh:

Updates the system log entries, starting from the current entry ID.



Clear:

Flushes the selected log entries.



|<<:

Updates the system log entries, starting from the first available entry ID.



: Updates the system log entries, ending at the last entry currently displayed.



>>:

Updates the system log entries, starting from the last entry currently displayed.



>>|:

Updates the system log entries, ending at the last available entry ID.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды