Niveo NGSME48T4H Скачать руководство пользователя страница 211

Страница: 211 / 338

Chapter

3: Web Management

System - IP Status

PoE Switch User Manual | 211

3.2.1.3. System - IP Status

This page displays the status of the IP protocol layer. The status is defined by the IP

interfaces, the IP routes and the neighbour cache (ARP cache) status.

IP Interfaces
Interface

The name of the interface.

Type

The address type of the entry. This may be LINK or IPv4.

Address

The current address of the interface (of the given type).

Status

The status flags of the interface (and/or address).

IP Routes
Network

The destination IP network or host address of this route.

Gateway

The gateway address of this route.

Status

The status flags of the route.

Neighbour cache
IP Address

The IP address of the entry.

Link Address

The Link (MAC) address for which a binding to the IP address given exist..

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды