Niveo NGSME48T4H Скачать руководство пользователя страница 17

Страница: 17 / 338

Chapter 1: Product Overview

Hardware Installation

NGSME48T4H Switch User Manual | 17

1.3. Hardware Description

This section mainly describes the hardware of Full-Management PoE switch and gives a

physical and functional overview on the certain switch.

Front Panel

The front panel of the switch consists of 48 10/100/1000 Base-TX RJ-45 ports and 4 10

Gigabit SFP+ ports. The LEDs are also located on the front panel.

LED Indicators

The LED Indicators present real-time information of systematic operation status. Each of the

switch’s RJ45 port has two LEDs, the green LED indicates RJ45 connection status/data link,

and the amber LED indicates if that port is providing electrical power.

Also, port 49 to port 52 (SFP+ Ports) has their own LEDs that indicate data link.

LED

Color / Status

Description

No. of LEDs

10/100/1000M

Green On

Link Up

1~48

Green Blinking

Data Activating

PoE

Amber On

PD is connected

1~48

SFP+

Green On

Fiber Connected

49~52

Green Blinking

Receiving/Transmitting

Data

49~52

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды