Niveo NGSM48T2 Скачать руководство пользователя страница 308

Страница: 308 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 308

LACP statistics

This page provides an overview for LACP statistics for all ports.

Port

The switch port number.

LACP Received

Shows how many LACP frames have been received at each port.

LACP Transmitted

Shows how many LACP frames have been sent from each port.

Discarded

Shows how many unknown or illegal LACP frames have been discarded at each

port.

Buttons

Auto-refresh:

Click this box to enable an automatic refresh of the page at regular

intervals.

Refresh:

Click to refresh the page immediately.

Clear:

Clears the counters for all ports.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды