Niveo NGSM48T2 Скачать руководство пользователя страница 185

Страница: 185 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 185

Mirroring Configuration

Configure port Mirroring on this page.

To debug network problems, selected traffic can be copied, or mirrored, on a mirror

port where a frame analyzer can be attached to analyze the frame flow.

The traffic to be copied on the mirror port is selected as follows:

All frames received on a given port (also known as ingress or source mirroring).

All frames transmitted on a given port (also known as egress or destination

mirroring).

Port to mirror on

Port to mirror also known as the mirror port. Frames from ports that have either

source (rx) or destination (tx) mirroring enabled are mirrored on this port. Disabled

disables mirroring.

Mirror Port Configuration

The following table is used for Rx and Tx enabling.

Port

The logical port for the settings contained in the same row.

Mode

Select mirror mode.

Rx only

Frames received on this port are mirrored on the mirror port. Frames

transmitted are not mirrored.

Tx only

Frames transmitted on this port are mirrored on the mirror port. Frames

received are not mirrored.

Disabled:

Neither frames transmitted nor frames received are mirrored.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды