Niveo NGSM48T2 Скачать руководство пользователя страница 178

Страница: 178 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 178

QoS / DSCP Translation

This page allows you to configure the basic QoS DSCP Translation settings for all

switches. DSCP translation can be done in Ingress or Egress.

The displayed settings are:

DSCP

Maximum number of supported DSCP values are 64 and valid DSCP value ranges

from 0 to 63.

Ingress

Ingress side DSCP can be first translated to new DSCP before using the DSCP for

QoS class and DPL map.

There are two configuration parameters for DSCP Translation -

1. Translate

2. Classify

1. Translate

DSCP at Ingress side can be translated to any of (0-63) DSCP values.

2. Classify

Click to enable Classification at Ingress side.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды