Niveo NGSM48T2 Скачать руководство пользователя страница 175

Страница: 175 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 175

QoS / Port DSCP Configuration

This page allows you to configure the basic QoS Port DSCP Configuration settings

for all switch ports.

The settings relate to the currently selected stack unit, as reflected by the page

header.

The displayed settings are:

Port

The Port column shows the list of ports for which you can configure dscp ingress and

egress settings.

Ingress

In Ingress settings you can change ingress translation and classification settings for

individual ports.

There are two configuration parameters available in Ingress:

1. Translate

2. Classify

1. Translate

To Enable the Ingress Translation click the checkbox.

2. Classify

Classification for a port have 4 different values.

Disabled:

No Ingress DSCP Classification.

DSCP=0:

Classify if incoming (or translated if enabled) DSCP is 0.

Selected:

Classify only selected DSCP for which classification is enabled as

specified in DSCP Translation window for the specific DSCP.

All:

Classify all DSCP.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды