Niveo NGSM48T2 Скачать руководство пользователя страница 136

Страница: 136 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 136

IPMC / MLD Snooping / Port Group Filtering

MLD Snooping Port Group Filtering Configuration

Delete

Check to delete the entry. It will be deleted during the next save.

Port

The logical port for the settings.

Filtering Groups

The IP Multicast Group that will be filtered.

Adding New Filtering Group

Click to add a new entry to the Group Filtering table. Specify the Port and Filtering

Group for the new entry. Click "Save".

Buttons

Save:

Click to save changes.

Reset:

Click to undo any changes made locally and revert to previously saved

values.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды