MOUNTING THE BATTERY
Warning: For safety reasons, a cyclist should never be tethered to
the bike. If the headlamp is mounted to the helmet, do not mount
the battery to the frame. Conversely, if the headlamp is mounted
to the handlebar, do not place the battery in a pocket or pack.
Frame Mount
1. Thread the hook/loop straps through the two slots on the bottom
of the battery.
2. Attach the concave surface of the battery to a safe,convenient
location on the frame (typically under the top or down tube),
placing the hook/loop strap over the tube, but under any shift
or brake cables. The cable from the battery should extend
toward the stem.
3. Secure the headlamp and battery cable to the frame using the
thin hook/loop strapettes. Make sure the cables do not interfere
with any moving parts.
OPERATION
1. Connect the headlamp cable to the battery.
2. Press and release the headlamp power button to turn the light on.
Cycle through the four brightness levels by pressing and releasing
the power button.
3. To access the daylight safety flash mode, press and hold the
power button until the headlamp starts to flash.
4. With the headlamp in flash mode, press and release the power
button to access beacon, SOS or walk modes. From walk mode
you can return to normal mode by pressing and releasing the
power button.
5. To turn the headlamp off from normal, flash or walk modes, press
and hold the power button until the headlamp shuts off.
6. Always disconnect the battery from the headlamp when
transporting the light system. This prevents accidentally
turning on the headlamp, which may cause overheating
and potential damage from high heat or even a risk of fire.
PROTECTING YOUR INVESTMENT
Properly charge your battery to maximize its lifespan (see the
“Battery Charging and Care” section for detailed information).
The Pro 2800 / 3600 Enduro will perform in wet weather conditions,
but submerging it in water will damage the system.
SUPPORT
If you experience difficulties during product installation or operation,
NiteRider™ provides free telephone support on weekdays from
8:00 am to 4:30 pm (Pacific Time) at 800.466.8366, Ext 4.
You may also e-mail us at [email protected].
WARRANTY
NiteRider™ stands behind its products with the following warranties:
• Lifetime warranty on all mechanical components
• 2 Years on electrical components
• 1 Year on rechargeable batteries
To obtain warranty service, it is preferable to have your original
sales receipt. Contact the NiteRider™ Customer Service
Department at 800.466.8366, Ext. 4 to obtain a Return
Merchandise Authorization (RMA) number. The RMA number
must be prominently displayed on the outside of your package.
The product must be properly packaged to prevent damage
in transit.
For complete warranty information, please visit our website at
www.NiteRider.com.
RUN TIMES
RIDING AT NIGHT CONT.
• Carry an auxiliary light and emergency supplies
• Make sure the headlamp, mounting bracket
and battery are securely fastened
• Always disconnect the battery from the headlamp
when transporting the light system
NiteRider™ Technical Lighting Systems, Inc.
8295 Aero Place, Suite 200
San Diego, CA 92123
www.NiteRider.com
OPERATION (cont.) Fuel Gauge
The 8-step, LED Fuel Gauge is located on top of the headlamp in
front of the power button. When all four LED’s are lit solid green,
the battery is fully charged. As the battery discharges ⅛ increments
of capacity, the LED’s from right to left, successively go from
solid green to blinking green, to out. With only the final ⅛ capacity
remaining one LED blinks red. At this time, the headlamp should
be turned off and the battery recharged.
BATTERY CHARGING AND CARE
1. Plug the AC Adapter into an electric outlet, then plug the cable
from the AC Adapter into the battery.
2. The LED indicator on the battery will turn red while the battery
is charging. When the battery is fully charged, the LED will
turn blue.
3. Unplug the AC Adapter from the battery by grasping the
connectors rather than the cable.
4. Leaving the battery and AC Adapter connected indefinitely will
not harm the battery or AC Adapter.
5. When storing for an extended period of time, charge the battery
every three months to maximize its lifespan.
USB OUTPUT PORT
Your battery pack is equipped with a USB output port for
convenient recharging of electronic devices.
1. Plug in your USB adapter cord (not supplied) into USB output
port, then connect your electronic device to charge.
Please note to power off lighting system before recharging your electronic device.
RIDING AT NIGHT
While a Pro 2800 / 3600 Enduro lighting system will improve your
view, control and enjoyment of night riding, please remember that
cycling at night is an inherently dangerous activity. In addition to
using your lighting system properly and riding with extreme caution,
NiteRider™ urges you to:
• Never ride alone
• Always let someone know where you are going
• Wear a helmet and reflective clothing
*Run times are approximations and will vary.
**Race mode is intended for endurance races.
PRO 2800 ENDURO REMOTE
Low
6:00h
825 Lumens
Med 3:00h
1400 Lumens
High 1:30h
2800 Lumens
Flash >56:00h
Race 17:00h
375 Lumens
Walk 56:00h
125 Lumens
PRO 3600 ENDURO REMOTE
Low
6:00h
1000 Lumens
Med 3:30h
1800 Lumens
High 1:30h
3600 Lumens
Flash >16:30h
Race 16:30h
450 Lumens
USB OUTPORT PORT
