Nitek ER8500U Скачать руководство пользователя страница 1

Model  ER16500U / ER8500U

 

 

Installation and 

Operation Manual 

Introduction 

The ER8500U and ER16500U are fully functional POE network switches with 802.3AT power output on each of the 
network ports and can operate with all standard Ethernet devices up to 100 meters. Additionally, when used with the 
ET1500U transmitter the system allows for cable runs of 600 meters or 2000 feet and will supply both a network 
connection and POE power. 

The ER8500 has 8 network ports and 1 LAN port and the ER16500 has 16 network ports 

and 2 LAN ports. 

Each of the network ports support standard Ethernet 10/100Mb network traffic and the LAN ports 

support standard Ethernet 10/100/1000Mb network traffic. The LAN ports do not supply POE. 

 

NITEK

 

®

 

De Schans 19-21 2a 
8231 KA Lelystad 
Tel: +31(0)320-2300005  
Fax: +31(0)320-282186  
E-mail: [email protected] 
WWW.NITEK.NL 

USA 

5410 Newport Drive, # 24 
Rolling Meadows, IL  60008 
Phone: (847) 259-8900  
Fax: (847) 259-1300   
E-mail: [email protected]  
WWW.NITEK.NET 

EUROPE 

122911 

2) Connect up the network outputs of the unit. The network ports are designed for connection with standard Ethernet 

cables. The network ports are 10/100Mb speed and will run at the highest possible speed given the wire conditions. 
This system normally operates at 100Mb over 600 meters of cable. We refer to the cable between the Head-end and 
the transmitter as the Link cable. The speed of the connection is indicated on the network port of the unit. A 
transmitter or other network device must be connected at the other end of the network cable for the connection speed 
to be indicated.    

681200114 

Head-end Installation  
ER8500U and ER16500U 

 

1) 

The ER8500U / ER16500U can be rack mounted, wall mounted or used as desk top unit. Use the included mounting 
ears in the front or back of the unit depending on your needs. The mounting ears can also be turned to the bottom of 
the unit for wall mounting if needed. When mounting the unit be sure to leave space on the sides for airflow into the 
cooling fans and some space on top of the unit for air to exit the unit.  

 

Front 

Back 

Rack Mounting 

Options 

Wall Mounting 

Options 

UTP Network Ports 

LAN Ports 

Содержание ER8500U

Страница 1: ... NET EUROPE 122911 2 Connect up the network outputs of the unit The network ports are designed for connection with standard Ethernet cables The network ports are 10 100Mb speed and will run at the highest possible speed given the wire conditions This system normally operates at 100Mb over 600 meters of cable We refer to the cable between the Head end and the transmitter as the Link cable The speed...

Страница 2: ...on the port LEDs Make sure your network switch can handle the ex pected data i e do not use a 100Mb network switch if you expect 300Mbps of data 4 Connect main power to the ER8500 ER16500 using a proper IEC power cord A power cord is supplied in the box with your ER8500 ER16500 unit 5 After completing the installation of the Head end equipment transmitter units must be installed at the camera remo...

Страница 3: ...Ethernet device to the transmitters Network Port If the device requires PoE power the POE OUT green LED on the Link Port will turn on followed by the LINK STATUS LED on the Network Port The IP camera or other Ethernet device should now be ready to operate Continue installing the remaining transmitters as needed Connector LED OFF ON FLASHING Network Port Power No power Power Good Link Status No Eth...

Страница 4: ...head end to transmitter The POE POWER CHART on the previous page will indicate the maximum power available for your length of cable 11 If the needed level of power is not available for the length of cable used alternate options are available One method is to directly power the transmitter with a 48VDC power supply as shown below Nitek PS48 When powered di rectly from a 48VDC supply the transmitter...

Отзывы: