877-NINJA-USA (646-5287) for assistance.
186 Virginia Rd, Crystal, Lake, IL 60014 Ph: 877-NINJA-USA (646-5287)
START UP GUIDE FOR OPTIMAL PERFORMANCE
-MAXIMUM INPUT PRESSURE OF 500PSI
-SET REFERENCE GAUGE TO 80PSI
-FIRE ROUNDS OVER CHRONOGRAPH
(Pressure may drop)
-INCREASE PRESSURE UNTIL STABLE AND DESIRED
VELOCITY IS ACHIEVED
-ONCE VELOCITY IS STABLE AT DESIRED LEVEL, INSTALL
TOURNAMENT LOCK ZIP TIE IF REQUIRED BY FIELD.
Proudly made in USA
NINJA LPRV2 LOW PRESSURE REGULATOR MADE IN USA
If you have any que
s�
ons or require help please call our 877-NINJA-USA (646-5287) for assistance.
186 Virginia Rd, Crystal, Lake, IL 60014 Ph: 877-NINJA-USA (646-5287)
Page | 5
REASSEMBLY: Reference figure 2
1.
Reinsert LPRV2 piston # 9 pin- side
fi
rst. Be certain the pin enters the center hole (Figure 3: X)
2.
Reinsert LPRV2 Main Spring #10, roughly center the spring on the piston.
3.
Verify the LPRV2 Adjuster is fully threaded into the LPRV2 Cap, fully turned counterclockwise.
4.
Thread, clockwise, the LPRV2 Cap onto the LPRV2 Body
NO GAP BETWEEN LPRV2 BODY AND
LPRV2 CAP.
5.
Reinstall the LPRV2 Maintenance Access Locking set screw #12,
DO NOT OVER TIGHTEN!
6.
Re-chronograph using the quick start guide in this manual.
REVISION JANUARY 2018
NINJA LPRV2 LOW PRESSURE REGULATOR MADE IN USA
If you have any que
s�
ons or require help please call our 877-NINJA-USA (646-5287) for assistance.
186 Virginia Rd, Crystal, Lake, IL 60014 Ph: 877-NINJA-USA (646-5287)
Page | 1
WARNING: THIS IS NOT A TOY IMPROPER USE CAN RESULT IN INJURY OR DEATH DO NOT USE THE LPR
PRIOR TO READING THIS MANUAL IN ITS ENTIRETY
The Ninja LPRV2 is a low pressure regulator for Air soft markers.
Construc
�
on: Aluminum.
Inlet Pressure: Max 500 PSI
Adjustment Range: 0 -160 PSI
Rese
�
ng Relief Valve: 140-150 PSI,
NOT SERVICEABLE DO NOT REMOVE OR TAMPER WITH.
Lub
rica�
on: Any Silicone based,
NON-PETROLEUM LUBRICANT.
Adjustment: 3/16” Allen wrench
Tournament legal: Can be locked out with zip
�e.
Pressure Gauge: 0-160 PSI
Piston: 015-90 red urethane oring for ease of maintenance.
Break In Period: 1000-3000 Cycles
Maintenance kit included (Quan
�t
y (2) of #7 red oring 015 )
The Ninja LPRV2 is designed to be used with a standard regulated paintball air source.
Paintball air source is available in 3000 and 4500 psi bo
�
les.
The paintball tank must have a
regulator, which regulates the air source the Max regulator output is
500 psi. Ninja offers a full
line of air systems, visit www.ninjapaintball.com
Figure 1.
D
C E
F
B A
Features:
A.
Pressure adjustment.
B.
Tournament Lock zip
�
e holes.
C.
Maintenance only access lock set screw.
D.
Pressure Relief Valve assembly.
E.
Low Pressure Reference Gauge.
F.
Low Pressure Quick Disconnect.
NINJA LPRV2 LOW PRESSURE REGULATOR MADE IN USA
If you have any que
s�
ons or require help please call our 877-NINJA-USA (646-5287) for assistance.
186 Virginia Rd, Crystal, Lake, IL 60014 Ph: 877-NINJA-USA (646-5287)
Page | 1
WARNING: THIS IS NOT A TOY IMPROPER USE CAN RESULT IN INJURY OR DEATH DO NOT USE THE LPR
PRIOR TO READING THIS MANUAL IN ITS ENTIRETY
The Ninja LPRV2 is a low pressure regulator for Air soft markers.
Construc
�
on: Aluminum.
Inlet Pressure: Max 1000 PSI
Adjustment Range: 0 -160 PSI
Rese
�
ng Relief Valve: 140-150 PSI,
NOT SERVICEABLE DO NOT REMOVE OR TAMPER WITH.
Lub
rica�
on: Any Silicone based,
NON-PETROLEUM LUBRICANT.
Adjustment: 3/16” Allen wrench
Tournament legal: Can be locked out with zip
�e.
Pressure Gauge: 0-160 PSI
Piston: 015-90 red urethane oring for ease of maintenance.
Break In Period: 1000-3000 Cycles
Maintenance kit included (Quan
�t
y (2) of #7 red oring 015 )
The Ninja LPRV2 is designed to be used with a standard regulated paintball air source.
Paintball air source is available in 3000 and 4500 psi bo
�
les.
The paintball tank must have a
regulator, which regulates the air source the optimal regulator output is 500 psi. Ninja offers a full
line of air systems, visit www.ninjapaintball.com
Figure 1.
D
C E
F
B A
Features:
A.
Pressure adjustment.
B.
Tournament Lock zip
�
e holes.
C.
Maintenance only access lock set screw.
D.
Pressure Relief Valve assembly.
E.
Low Pressure Reference Gauge.
F.
Low Pressure Quick Disconnect.