NimbeLink Skywire NL-SWDK Скачать руководство пользователя страница 26

Страница: 26 / 26

3. APN Setup

3.1. Overview

GSM and LTE-based Skywire modems can be setup to use different APNs. APNs are

used by devices and cellular networks to initialize and properly set up a cellular

connection. Accordingly, in order to connect to a cellular network, it is crucial to ensure

that the proper APN is set on the device.

If you activated your Skywire modem on

https://go.nimbelink.com

, use the APN's

defined in Section 3.2. For data plans not activated through NimbeLink please reach out
to your carrier for APN configuration details.

3.2. Common APNs and Their Respective Carriers

The table below contains a list of common APNs and their respective carriers. It is

important to use the APN that corresponds to the proper carrier and the specific IP

address configuration. Failure to do so will result in failed cellular network connections.

Cellular Carrier

Common APNs

Description

Verizon

NIMBLINK.GW12.VZWENTP

APN for Verizon devices activated

through Go.NimbeLink.com

MW01.VZWINTERNET

APN for devices upgraded to a Public

Static IP address

AT&T

iot0718.com.attz

AT&T Direct APN

T-Mobile

m2mglobal

T-Mobile Direct APN

4. Common Next Steps

Once the network setup and testing is complete, you are ready to start developing with

your Skywire modem. Common application examples include sending and receiving

SMS messages, FTP file transfer, TCP/UDP packets, and using the modem with an

external microcontroller, such as an Arduino. Please consult these application notes on

the Skywire Development Kit page (

http://nimbelink.com/skywire-development-kit/

) or

your Skywire-specific page for specific examples of each type of operation.

PN 30005 rev 23

Содержание Skywire NL-SWDK


























Результаты поиска

Содержание Skywire NL-SWDK

Отзывы:

Бренды по названию

Популярные бренды

NimbeLink Skywire NL-SWDK, Руководство пользователя

Результаты поиска

Содержание Skywire NL-SWDK

Отзывы:

Бренды по названию

Популярные бренды