NimbeLink Skywire NL-SWDK Скачать руководство пользователя страница 23

Страница: 23 / 26

AT+CGDCONT=1,"IPV4V6","APN"

Where

APN

is replaced with the individual APN for your network. The terminal

program should respond with:

Note: Consult Section 3: APN Setup for help with your APN.

Finally, turn on cellular functionality by issuing the following command:

AT+CFUN=1

The modem should respond with:

After turning on cellular functionality, the Skywire will automatically activate the

specified PDP context. To confirm that the PDP context has indeed been

activated, issue the following command:

AT+CGACT?

The terminal should respond with:

+CGACT: 1,1

If the modem responds with the above line, then the PDP context has been

successfully activated.

2.16. Check Network Registration

The commands to check network registration differ depending on the modem

technology your modem is using. 2G/3G devices will use the AT+CREG

command and LTE devices will use the AT+CEREG or AT+CGREG commands.

2.16.1.

2G/3G Network Registration

To check network registration for these modems:

NL-SW-1xRTT-A

NL-SW-1xRTT-S

NL-SW-1xRTT-V

NL-SW-EVDO-A

NL-SW-EVDO-V

NL-SW-GPRS

NL-SW-HSPA

NL-SW-HSPA-B

follow this procedure:
In the terminal program, type the command:

AT+CREG?

followed by the Enter key, and the terminal should respond with:

+CREG: 0,1

+CREG: 0,5

PN 30005 rev 23

Содержание Skywire NL-SWDK


























Результаты поиска

Содержание Skywire NL-SWDK

Отзывы:

Бренды по названию

Популярные бренды

NimbeLink Skywire NL-SWDK, Руководство пользователя

Результаты поиска

Содержание Skywire NL-SWDK

Отзывы:

Бренды по названию

Популярные бренды