Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 79

Страница: 79 / 232

Electrical System

Service Manual – Floortec R 870

Dynamotor Carbon Brush Check/Replacement (Floortec R 870 Petrol)

Disassembly

Drive the machine on a level floor.

2 Turn the ignition key to “0” and engage the parking brake

3 Open the engine compartment hood with the handle and fasten it with the support rod Disconnect the

batteries

Remove the machine right side bulkhead, by lifting it to disengage it from the fasteners.

5 Remove the two screws (A) and remove the case (B)

If necessary, clean the external side of the dynamotor (C) in the area of the protection band (D).

7 Disengage the cam lever (E) and remove the protection band (D) of the dynamotor (C)

P200122

Содержание 9084404010









































































































































































































































Результаты поиска

Содержание 9084404010

Отзывы:

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 79 / 232

Результаты поиска

Содержание 9084404010

Отзывы: