Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 215

Страница: 215 / 232

Wheel System, Traction

215

Service Manual – Floortec R 870

Brake Cable Disassembly/Assembly

Disassembly

If possible, place the machine on a hoisting system.

2 Turn the ignition key to “0” Ensure that the machine cannot move by placing opposite wedges (A) on the

rear wheels

Remove the left side broom, if equipped.

Steer the front wheel to the right, about 90°.

5 Unscrew nut and locknut (B) then remove the brake cable (C) from the brackets (D)

Under the brake pedal, loosen the nut-locknut (H) of the brake cable (C).

7 Remove the clip with the pin (F)

8 Disconnect from the brake pedal the terminal (G) of the cable (C) of the brake

9 Remove the cable (C) through the slot (L)

P200200

Содержание 9084404010









































































































































































































































Результаты поиска

Содержание 9084404010

Отзывы:

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 215 / 232

Результаты поиска

Содержание 9084404010

Отзывы: