Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 209

Страница: 209 / 232

Wheel System, Traction

209

Service Manual – Floortec R 870

PAR

PARAMETER

DEFAULT

NOTE

PIN 11-J1 HARDWARE
CONFIGURATION

N.C. SWITCH

Parameter connected to the hardware configuration

(DO NOT MODIFY!)

A1 ALARM ENABLING

DISABLE

Parameter connected to the hardware configuration

(DO NOT MODIFY!)

A2 ALARM ENABLING

DISABLE

Parameter connected to the hardware configuration

(DO NOT MODIFY!)

A3 ALARM ENABLING

ENABLE

Parameter connected to the hardware configuration

(DO NOT MODIFY!)

A4 ALARM ENABLING

ENABLE

Parameter connected to the hardware configuration

(DO NOT MODIFY!)

A12 ALARM ENABLING

DISABLE

Parameter connected to the hardware configuration

(DO NOT MODIFY!)

Содержание 9084404010









































































































































































































































Результаты поиска

Содержание 9084404010

Отзывы:

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 209 / 232

Результаты поиска

Содержание 9084404010

Отзывы: