manualshive.com logo in svg

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 206 / 232

Поделиться
Скачать
Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 206

Wheel System, Traction

206

Service Manual – Floortec R 870

Troubleshooting

Trouble

Possible causes

Remedy

The machine does not move

The batteries are discharged or its connections are not 

efficient

Charge the batteries or clean/repair the 

connections

The drive pedal control assembly (R1) is broken

Replace

The drive system electronic board (EB1) is faulty

Replace

The wiring harness is damaged

Check the electrical connections/repair the 

wiring harness

The carbon brushes of the driving wheel (M0) are worn/

damaged

Replace the carbon brushes/replace the driving 

wheel

The ignition key (SW1) is not working

Replace

The driver’s seat safety microswitch (SW7) is broken

Replace

The brake does not operate

The braking masses are worn

Replace

The brake cable is misadjusted

Adjust it

The machine does not move 

when pressing the drive pedal 

and the drive system warning 

light (red) flashes.

The drive pedal has been pressed before or at machine 

start-up.

Start up the machine without pressing the drive 

pedal.

Drive system failure.

Turn off the machine and then turn it on again.

If the trouble persists, contact the Service 

Center.

Содержание 9084404010









































































































































































































































Отзывы:

Нет отзывов