Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 202

Страница: 202 / 232

Wheel System, Traction

202

Service Manual – Floortec R 870

Wheel System, Traction

Functional Description

The main components for the drive system are: the driving wheel assembly with integrated disc brake, the

drive pedal, the electronic board, forward/reverse gear switch and the brake pedal with parking brake lever.

The direction of travel is defined by the switch on the dashboard. If the switch is set to reverse, the reverse

gear buzzer starts to sound until the forward gear is not restored

On the driving wheel there is a disc brake keyed to a reduction unit fast shaft

The brake pedal activates the disc brake piston with a sheathed cable The parking brake lever mechanism is

integrated in the brake pedal

The driving wheel (M0) is powered by the drive system control electronic board (EB1)

The driving wheel is electronically protected by the drive system control electronic board (EB1), which limits

the current supplied at the values set in the relevant parameters (see parameters 19, 20, 21 in Drive System

Electronic Board Parameter Table)

The electronic board power circuit (EB1) is powered through the safety electromagnetic switch (ES0)

The electromagnetic switch (ES0) is activated by the same electronic board (EB1), after the first check on the

conformity of the input conditions, when it receives the start-up signal by the ignition switch circuit (SW1)

through the relay (K4)

The main control inputs of the electronic board (EB1) are the hall-effect pedal (R1) and the forward/reverse

gear switch (SW2)

Other inputs of the electronic board (EB1) are: the driver’s seat microswitch (SW7) and the lifted hopper sen

sor (S1) signal The drive system is inhibited when the microswitch (SW7) does not detect the operator on

the driver’s seat, but when the sensor (S1) detects that the hopper is lifted, the maximum machine speed is

decreased to a safety value (see parameter 12, in Drive System Electronic Board Parameter Table).

Upon start-up (with the ignition switch SW1) or when the driver’s seat microswitch signal (SW7) is inter

rupted and then restored, the system is always set to forward speed. Pressing the forward/reverse gear switch

(SW2) changes to reverse gear until the switch is pressed again. When the reverse gear is selected, the warn

ing light on the switch (SW2) and the buzzer (BZ1) turn on.

The position of the drive pedal (R1) determines the machine speed The safety condition for drive system ac-

tivation is that the drive pedal (R1) is totally released (machine stopped) when the system is turned on (with

the ignition switch SW1)

When the machine is stopped, the output signal for R1 is less than 1V.

When the machine reaches the maximum speed, the output signal for R1 is higher than 5V.

This calibration should be correct for 100% of pedals. Otherwise, if a different pedal calibration is necessary,

perform the following learning procedure for the electronic board:

1 Connect the programmer (9097297000) and enter the potentiometer calibration enabling page

Confirm by pressing the MODE key

Release the pedal and confirm by pressing the MODE key

Press the pedal until the end of stroke (max. speed) and confirm by pressing the MODE key

Содержание 9084404010









































































































































































































































Результаты поиска

Содержание 9084404010

Отзывы:

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 202 / 232

Результаты поиска

Содержание 9084404010

Отзывы: