Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 171

Страница: 171 / 232

Main Broom System

171

Service Manual – Floortec R 870

Skirt Disassembly/Assembly (Continues)

Front Skirt Removal and Installation

Note:

It is advisable to place the machine on a hoisting system.

10 Remove the main broom

11 Remove the side brooms

On the left front side of the front skirt (D), disengage the clip (E) then disconnect the terminal (F) of the

skirt lifting tie rod form the bracket (G)

13 Remove the six nuts (H) then remove the strap (I) from the main broom compartment

14 Remove the front skirt assembly (J) from the front

At the workbench, unscrew the six nuts (K) and remove the section bar (L) and the strap (M).

16 Retrieve the front skirt (N)

17 Install the front skirt (N) in the reverse order of disassembly

18 Check the front skirt height

P200244

Содержание 9084404010









































































































































































































































Результаты поиска

Содержание 9084404010

Отзывы:

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 171 / 232

Результаты поиска

Содержание 9084404010

Отзывы: