Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 140

Страница: 140 / 232

Hopper System

140

Service Manual – Floortec R 870

Removal and Installation

Closed Hopper Sensor Disassembly/Assembly and Adjustment

Disassembly

Drive the machine on a level floor.

2 Turn the ignition key to “0” and engage the parking brake

3 Open the battery/engine compartment hood with the handle and fasten it with the support rod

Disconnect the battery connector (Floortec R 870 Battery) - Disconnect the batteries (Floortec R 870

Petrol/LPG)

On the right rear upper side of the machine, remove the connector (B) of the closed hopper sensor (C)

from its housing (A)

5 Cut the fastening clamp (D) and disconnect the connector (B)

6 Remove the locknut (E) and remove the sensor (C) with the wiring harness

Assembly

Assemble the components in the reverse order of disassembly, and note the following:

• Adjust the distance (F) between the sensor (C) and the bracket (G) at 4-5 mm, then tighten the lock

nut (E)

4-5mm

P200216

Содержание 9084404010









































































































































































































































Результаты поиска

Содержание 9084404010

Отзывы:

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 140 / 232

Результаты поиска

Содержание 9084404010

Отзывы: