Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 129

Страница: 129 / 232

Engine System - LPG

129

Service Manual – Floortec R 870

Engine-Dynamotor Unit Disassembly/Assembly

Disassembly

1 Empty the LPG system (see the procedure in “LPG System Emptying”)

Drive the machine on a level floor.

3 Turn the ignition key to “0” and engage the parking brake

4 Open the engine compartment hood with the handle and fasten it with the support rod

5 Disconnect the batteries

Remove the machine right body side (A), by lifting it to disengage it from the fasteners.

Disconnect the LPG hose (B) from the carburettor (C), as shown in “LPG System Hose and Fitting

Disassembly/Assembly LPG”

Close with sealing plugs the disconnected fittings to prevent foreign materials from entering into the

system

P200215

Содержание 9084404010









































































































































































































































Результаты поиска

Содержание 9084404010

Отзывы:

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 129 / 232

Результаты поиска

Содержание 9084404010

Отзывы: