Nilfisk-ALTO 9084404010 Скачать руководство пользователя страница 128

Страница: 128 / 232

Engine System - LPG

128

Service Manual – Floortec R 870

Solenoid Valve Removal/Installation (Continues)

9 Disconnect the electrical connections (D) and (F)

10 Remove the fastening screws (G) of the pressure regulator assembly with valves (H)

11 Remove the pressure regulator assembly with valves (H)

At the workbench, remove the “T” fitting (I) from the fitting (L).

Remove the solenoid valve (J) from the fitting (K).

Unscrew the fitting (L) from the solenoid valve (J).

15 Retrieve the solenoid valve (J)

Assembly

16 Assemble the components in the reverse order of disassembly

17 Perform the LPG System Leakage Check (see the procedure in LPG System Leakage Check paragraph)

P200150

Содержание 9084404010









































































































































































































































Результаты поиска

Содержание 9084404010

Отзывы:

Nilfisk-ALTO 9084404010, Руководство по обслуживанию, Страница: 128 / 232

Результаты поиска

Содержание 9084404010

Отзывы: