Nilfisk-Advance SC401 17 B Скачать руководство пользователя страница 96

Страница: 96 / 173

Service Manual – SC401, SCRUBTEC 344

20 - Wheel System, Traction

Drive System Gear Motor Current Draw Test

WARNING:

This procedure must be performed by qualified personnel only and with the help of an

assistant.

Drive the machine on a level floor.

Use a suitable chock to raise one side of the machine approximately 2cm from the floor and allow one

drive wheel to turn freely

WARNING: Pay attention to the rotation of the driving wheel when performing the following steps.

3 Apply the amp clamp (A) on the positive cable (red) of the drive harness (B) near the Drive system gear

motor

Figure 6:

4 Rotate the Speed adjuster at maximum speed

5 Switch on the machine and activate the drive motor with at least one hand on the Operator’s presence

sensor

6 Check that the current draw is included between 1,5 and 2,5A at 24V

7 Release the Operator’s presence sensor

8 Switch off the machine and remove the amperometric clamp

9 If the amperage is higher, perform the following procedures to detect and correct the abnormal

amperage:

◦

Check if there is dust or debris preventing the wheel rotation

◦

If necessary, disassemble the motor (see “

Drive system gearmotor

” paragraph), and check the

condition of all its components

10 If the above-mentioned procedures do not lead to a correct amperage, the gearmotor must be replaced

Содержание SC401 17 B














































































































































































Результаты поиска

Содержание SC401 17 B

Отзывы:

Похожие инструкции для SC401 17 B

Бренды по названию

Популярные бренды

Nilfisk-Advance SC401 17 B, Руководство по обслуживанию

Результаты поиска

Содержание SC401 17 B

Отзывы:

Похожие инструкции для SC401 17 B

Бренды по названию

Популярные бренды