The VCS-2S is a wall-mount, standard-style volume control. It con-
nects between the speaker-level output of an amplifier, speaker
selector, etc. and a pair of speakers.
The VCS-2S adjusts the volume of speakers connected to it by
attenuating the amplifier signal. Niles volume controls use auto-
formers instead of L-pads for the volume controlling element.
This assures minimal internal power dissipation with virtually no
power wasted as heat.
B
L E N D I N G
H
I G H
F
I D E L I T Y
A N D
A
R C H I T E C T U R E
®
VCS-2S
PREMIUM STEREO VOLUME CONTROL
1. Make sure the amplifier
or receiver power is OFF
and set the volume to
minimum.
2. Set the VCS-2S volume
to maximum (fully clock-
wise).
3. If you are using a Niles
speaker selection system,
locate the ON/OFF button
which corresponds to the
speaker pair you wish to
play. Set it to the ON posi-
tion.
4. Turn on the amplifier or
receiver and select a
source, such as the tuner
or CD player.
5. Slowly turn up the
amplifier or receiver vol-
ume and set it to a com-
fortable (not maximum)
listening level. Be careful
not to overdrive or "clip"
your amplifier. If the
sound becomes muddy or
distorted, you have
reached the limit of your
amplifier’s volume capabil-
ity and should quickly
reduce the volume to
avoid damaging your
speakers.
6. Adjust the volume of
the speakers to the desired
listening level using the
VCS-2S. If all the speaker
pairs in your system are
equipped with Niles vol-
ume controls, you can
leave the amplifier or
receiver volume set at one
position and use the Niles
controls exclusively.
7. You can turn off the
speakers by turning the
knob on the VCS-2S fully
counter-clockwise, or by
pressing the ON/OFF but-
ton on your speaker selec-
tor.
Audio Power Handling
60 Watts/channel peak music power
Mounting
In-wall, fits into most 18 cu. inch sin-
gle-gang P-ring or electrical boxes at
least 2-9/16” deep
Wiring Requirements
Individual runs of 2-conductor speak-
er wire, 14-22 gauge
Unit Dimensions
2-3/4" wide x 4-1/2" high
Depth Behind Plate
2-7/8”
Niles Audio Corporation 12331 S.W. 130 Street Miami, Florida 33186 Tel: (305) 238-4373 Fax: (305) 238-0185
©1999 Niles Audio Corporation. All rights reserved. Niles, the Niles logo and Blending High Fidelity and Architecture are registered trademarks of Niles
Audio Corporation. Because Niles continuously strives to improve its products, Niles reserves the right to change product specifications without notice.
Printed in the USA 10/96 DS00111B
•
The VCS-2S uses a 12-position control, which is superior to 10-
position designs. You get a broader range of adjustment—there
are ten steps of attenuation instead of eight. Steps 11-6 attenu-
ate -3 dB per step; steps 5-2 are -6 dB per step. Step 12 is “full-
on” and step 1 is “full-off”.
•
Greater dynamic range — you get 42 dB of total attenuation
instead of the typical 20 or 30 dB.
•
POP-FREE switching between all steps.
•
100% tested, electronically and acoustically, for frequency
response, distortion and power handling. Printed circuit board
construction uses no hand wiring, assuring high reliability.
Frequency response: 20 Hz to 20 KHz ± 1.2 dB.
•
Isolated left and right channel grounds make it safe for use with
any amplifier.
•
May be used with 4, 6, or 8 Ohm speaker systems.
•
Power handling: 60 watts/channel peak music power.
•
Available colors: White, Bone, Almond, or Black.
•
Ten year parts and labor warranty.
•
Proudly made in the USA.
Introduction
Features and Benefits
Operation
Specifications
www.nilesaudio.com
