Nikon Total Station DTM-322 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 185

background image

3

Getting Started

20

Total Station DTM-322 Instruction Manual

Turning the Instrument On and Off

Turning on the instrument

1.

To turn on the instrument, press

[PWR]

. The start-

up screen appears. It shows the current
temperature, pressure, date, and time.

2.

To change the temperature or pressure value,
use

[^]

or

[v]

to move the cursor to the field that

you want to change. Then press

[ENT]

.

3.

If you want to initialize the horizontal angle,
rotate the alidade.

4.

Tilt the telescope until it passes the horizontal
position on Face-1.

Turning off the instrument

To turn the instrument off, press

[PWR]

and

[ENT]

.

Then do one of the following:

If you have entered your name or your company’s name in the Owner’s detail
field, the text from this field appears on the start-up screen. To set the Owner’s
detail field, go to

MENU > Settings > Other

. For more information,

see

Once you start to use an initialized HA, you must rotate the alidade to initialize the HA every time you turn on the
instrument. If you do this, you can maintain a fixed HA orientation even if the instrument has moved while it is
turned off.
If you tilt the telescope before you rotate the alidade, the horizontal angle is not initialized, and the instrument
uses the previous HA reading.

Press ...

To ...

[ENT]

again

turn off the instrument

the

Reset

softkey

reboot the program and re-start the instrument

«
...
32
33
34
35
36
...
»

Содержание Total Station DTM-322


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Total Station DTM-322

Бренд: Underground Magnetics Страницы: 48

Бренд: Vaisala Страницы: 2

Бренд: YOSensi Страницы: 26

Бренд: YOSensi Страницы: 26

WJ-NU301K Series

Бренд: i-PRO Страницы: 24

WJ-NU101K Series

Бренд: i-PRO Страницы: 18

Бренд: Cal Test Electronics Страницы: 12

Бренд: Velleman Страницы: 32

Бренд: LAUMAS Страницы: 12

Бренд: Roland Страницы: 32

Бренд: FuzzDog Страницы: 6

Бренд: Vega Страницы: 44

Бренд: Omega Страницы: 4

Бренд: Racelogic Страницы: 15

EnviroAlert EA200

Бренд: Winland Страницы: 3

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 47

NEO MP18X Series

Бренд: MA Страницы: 3

Nunes Instruments Propeller Type Water Current...

Бренд: V-tech Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды