Nikon Total Station DTM-322 Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 185

background image

5

Menu Key

104

Total Station DTM-322 Instruction Manual

Settings

To display the Settings menu, press

[2]

or select

Settings

on the MENU screen.

Use this menu to configure the initial job settings.

Angle

To open the Angle menu, press

[1]

or select

Angle

in

the Settings menu.

Distance

To open the Distance menu, press

[2]

or select

Distance

in the Settings menu

Some job settings, specified in the following sections, cannot be changed
once a job is created. If any of these settings are changed while a job is open,
a confirmation screen appears, asking you to create a new job with the new
settings, or to work with those settings without recording any data. For more
information, see

Settings, page 168

.

VA zero

Zenith/Horizon/Compass

The VA zero job setting cannot be changed once a job is created.

Resolution

1"/5"/10" or 0.2 mgon/1 mgon/2 mgon

HA

0 to BS/Azimuth

The HA job setting cannot be changed once a job is created.
When this field is set to Azimuth, the horizontal angle (HA) that appears and recorded is in Azimuth value. When
this field is set to 0 to BS, HA is in HA zero to BS value.

Scale

Numeric value between 0.999600 and 1.000400

.

T-P corr.

ON/OFF

Sea Level

ON/OFF

C&R corr.

OFF/0.132/0.200

The Scale, T-P corr., Sea Level, and C&R corr. job settings cannot be changed once a job is created.

«
...
116
117
118
119
120
...
»

Содержание Total Station DTM-322


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Total Station DTM-322

MIC TRAC MT-3000

Бренд: GAGEMAKER Страницы: 20

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: National Instruments Страницы: 15

Бренд: Solartron Mobrey Страницы: 34

Бренд: pts Diagnostics Страницы: 2

LeakTracker OIL-GLO ULTRA

Бренд: Spectroline Страницы: 12

350 Maritime V2

Бренд: TESTO Страницы: 106

Бренд: Velleman Страницы: 13

Бренд: A&D Страницы: 2

Бренд: Bulteh 2000 Страницы: 80

dry-cal dc-lite

Бренд: BIOS Страницы: 10

Бренд: dacell Страницы: 29

Бренд: VOLTCRAFT Страницы: 4

Бренд: GW Instek Страницы: 91

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды