Nikon NPL-632 Скачать руководство пользователя | Manualshive

Страница: 74 / 206

background image

4

Applications

60

Field Station NPL-632 Instruction Manual

6.

To finish the station setup after taking a distance
measurement, press

[ENT]

. ST and F1 records are

stored to the current job.

Advanced feature: Measuring F1 and F2

To take an angle shot and proceed to the next
measurement on Face-2, press the

F2

softkey.

To go directly to the Face-2 measurement after taking a
distance measurement to the BS on Face-1, flip the
telescope. The instrument automatically detects F1/F2.

Press

[ENT]

on Face-2. The delta screen appears.

To record a CP record which stores the averaged HA,
VA, and SD from the F1/F2 data, press the

CP

softkey.

To record only the ST and F1/F2 records, without a CP
record, press the

OK

softkey.

Sighting the backsight by entering the azimuth angle

1.

To enter the azimuth angle to the backsight
point, press

[2]

or select

Angle

in the Backsight

screen.

Backsight point

Azimuth

Station point

(Xi, Yi, Zi)

In

st

rum

e

nt

he

ig

ht

X

Z

X0

Y0

Y

«
...
72
73
74
75
76
...
»

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

Бренд: Keithley Страницы: 48

Бренд: DAKOTA ULTRASONICS Страницы: 25

Бренд: DAKOTA ULTRASONICS Страницы: 36

Бренд: Oceanic Страницы: 152

Бренд: Kaiterra Страницы: 8

Бренд: Kaiterra Страницы: 12

Бренд: Raycus Страницы: 40

Бренд: RaycoWylie Страницы: 31

Бренд: SAGEMCOM Страницы: 33

Professional Plus

Бренд: YSI Страницы: 28

Бренд: ZHYQ Страницы: 6

Бренд: P3 International Страницы: 1

Бренд: Panasonic Страницы: 1

Бренд: Tire-Safeguard Страницы: 6

Бренд: Circutor Страницы: 48

Бренд: Ramsey Electronics Страницы: 40

DigiFlow 6710M-22

Бренд: Savant Страницы: 3

Бренд: SBS Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды