Nikon NPL-302 Series Скачать руководство пользователя | Manualshive

Страница: 30 / 234

background image

2

Preparation

10

Pulse Laser Station NPL-302 Series Instruction Manual

Unpacking and Packing the Instrument

2.1

Note –

Handle the NPL-302 series instrument gently to protect it from shocks and

excessive vibration.

Unpacking

21.1

To unpack the instrument, grip the carrying
handle and gently remove the instrument
from the carrying case.

Packing

21.2

Note –

Store the instrument with the battery

pack attached.

To pack the instrument back into the carrying
case:

1.

Set the telescope in the horizontal face-1 position.

2.

Align the

W

storage mark on the bottom of

the face-1 keyboard with

W

the

mark on the

leveling base clamp knob.

3.

Lightly fasten the clamp knobs.

4.

Place the instrument in the carrying case.

Note –

When packing the charger (Q-75U/E) in

the plastic carrying case, make sure that you
store it as shown on the sticker inside the case.
Make sure that the battery charger cable is not
pinched when you close the case cover.

Charging and Discharging the Battery Pack

2.1

Before charging the battery pack, read the warnings (also listed in the Safety section
at the front of this manual) and the following notes.

C

Warning –

Use only the specified battery charger (part number Q-75U/E) to

charge the battery pack (part number BC-65). Using other chargers, such as
a charger with part number Q-7U/E or Q7C, may cause the battery pack to
catch fire or rupture.

«
...
28
29
30
31
32
...
»

Содержание NPL-302 Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-302 Series

Бренд: YOKOGAWA Страницы: 3

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 16

Бренд: i-SENS Страницы: 50

Бренд: jenway Страницы: 50

Бренд: jenway Страницы: 62

Бренд: Oceanic Страницы: 152

Бренд: Kaiterra Страницы: 8

Бренд: Kaiterra Страницы: 12

Monitoring System 500 II DC

Бренд: Didactum Страницы: 2

Бренд: KROHNE Страницы: 56

Бренд: Xylem Страницы: 10

Бренд: Lasertec Страницы: 32

Бренд: IDEAL Страницы: 20

Бренд: L.R. Baggs Страницы: 6

Бренд: Princeton Instruments Страницы: 28

Бренд: Kane Страницы: 52

Micro Alti Vario Plus

Бренд: Fairhaven Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды