Nikon NPL-302 Series Скачать руководство пользователя | Manualshive

Страница: 132 / 234

background image

4

Applications

112

Pulse Laser Station NPL-302 Series Instruction Manual

7.

Enter a PT (and CD) value. The height of
target (HT) defaults to the value used in the
last measurement.

8.

To record the corner point, press

[ENT]

.

Sample records

SS, 58, 0.0000, 48.3304, 169.19165, 82.02470, 10:52:37, FLOOR2
CO, PT1, 1.0080, 48.3020,169.19165, 83.58565
CO, PT2, 1.0080, 48.3155,128.54250, 85.42440
CO, O/S MSR:40 0.0000 0.0000 169.20370 87.02340

Measuring circle offsets

40.1

1.

To enter the circle center calculation function,
press

[7]

or select

Circle

in the Offset menu.

If you have not taken a measurement to the
circle before entering this function, a
temporary measurement screen appears.

2.

Sight any point on the surface of the circle and
press

[MSR1]

or

[MSR2]

.

The calculated corner point is stored as an SS record.
The next three or four comment records are measured points. For example:
CO, Point name (fixed to PT1, PT2 etc.), HT, SD, HA, VA.

If you use a prism attached to the surface of the circle for the distance
measurement, press the

+SD

softkey to eliminate the offset error (from the attached

point to the measured surface of the prism) before you press

[ENT]

.

«
...
130
131
132
133
134
...
»

Содержание NPL-302 Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-302 Series

Бренд: Danfoss Страницы: 8

Бренд: Bacharach Страницы: 64

Бренд: DAE Страницы: 28

Бренд: QuadTech Страницы: 76

Wind Monitor Series

Бренд: Campbell Страницы: 38

Бренд: Favero Electronics Страницы: 12

Бренд: Facom Страницы: 48

SignalHawk SH-36S-PC

Бренд: BIRD Страницы: 137

KEITHLEY 4200-CVU-PWR

Бренд: Tektronix Страницы: 6

Amplitude T Series

Бренд: OTOVATION Страницы: 15

Бренд: YOKOGAWA Страницы: 104

Бренд: iBike Страницы: 52

EZP3 EASY Piano

Бренд: Lowrey Страницы: 59

Бренд: Apera Страницы: 2

Mini-SuperGraph II

Бренд: NOMIS Seismographs Страницы: 44

Бренд: AL Страницы: 2

Бренд: HEIDENHAIN Страницы: 28

Бренд: Perel Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды