Nikon HQA46480 Скачать руководство пользователя

Страница: 5 / 185

Total Station DTM-322 Instruction Manual

Warnings and Cautions

The following conventions are used to indicate safety instructions:

WARNING –

Warnings alert you to situations that could cause death or serious injury.

CAUTION – Cautions alert you to situations that could cause injury or property damage.

Always read and follow the instructions carefully.

Warnings

Before using the instrument, read the following warnings and follow the instructions
that they provide:

WARNING –

Never look at the sun through the telescope. If you do, you may damage or lose

your eyesight.

WARNING –

The DTM-322 is not designed to be explosion-proof. Do not use the instrument in

coal mines, in areas contaminated with coal dust, or near other flammable substances.

WARNING –

Never disassemble, modify, or repair the instrument yourself. If you do, you may

receive electric shocks or burns, or the instrument may catch fire. You may also impair the
accuracy of the instrument.

WARNING –

To charge the battery, use only the battery charger that is supplied with the

instrument. Do NOT use any other charger or you may cause the battery to catch fire or
rupture.

WARNING –

Do not cover the battery charger while the battery is being recharged. The

charger must be able to dissipate heat adequately. Coverings such as blankets or clothing can
cause the charger to overheat.

WARNING –

Avoid recharging the battery in humid or dusty places, in direct sunlight, or near

heat sources. Do not recharge the battery when it is wet. If you do, you may receive electric
shocks or burns, or the battery may overheat or catch fire.

WARNING –

You should take care not to short circuit the contacts. Short circuits can cause the

battery to catch fire or burn you.

WARNING –

Never burn or heat the battery. Doing so may cause the battery to leak or rupture.

A leaking or ruptured battery can cause serious injury.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды