Nikon HQA46480 Скачать руководство пользователя

Страница: 44 / 185

Getting Started

Total Station DTM-322 Instruction Manual

Quick code measurement mode

To activate Quick code measurement mode,
press

[MODE]

in the BMS.

The PT field shows the default point name.

Press any numeric key (

[0]

through

[9]

) to start

measuring and recording points.

A list of the numeric keys and their assigned
feature codes appears on the right side of the
screen.

For example, when you press

[6]

, the code

assigned to 6 is selected, and the instrument
starts a measurement.

If you have set the record mode to Confirm (see

Measurement settings, page 45

), the Record PT

screen appears after each measurement.

Do one of the following:

–

To record the point, press

[ENT]

–

To return to the BMS, press

[ESC]

To return to the BMS from the Qcode screen, press

[MODE]

[ESC]

[COD]

key

In the BMS, press

[COD]

to change the default feature code that will appear in the CD

field when you record a point.

Setting the default code

When you press

[COD]

in the BMS, a window for

entering the feature code appears.

You can use the

List

and

Stack

softkeys to enter the

code.

To assign a new feature code to a numeric key, press [

[v]

to highlight the code that you want to change. Then

press the

Edit

softkey.

You can use the

DSP

softkey to change the values shown in the measurement box, in the same way as you use

the

[DSP]

key in the Basic Measurement Screen (BMS).

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды