Nikon HQA46480 Скачать руководство пользователя

Страница: 43 / 185

Total Station DTM-322 Instruction Manual

Getting Started

To save your changes, press the

Save

softkey. Alternatively, highlight the last

item for DSP3 and press

[ENT]

. The DSP screens show the items you have

selected.

[MODE]

key

Use the

[MODE]

key to change the keyboard mode for the current screen.

Changing input mode while entering points or codes

When the cursor is in a point (PT) or code (CD) field,
press

[MODE]

to change the input mode between

alphanumeric (

) and numeric (

The input mode indicator in the status bar changes to
show the current input mode.

Except for the (none) item, you cannot display the same item on more than one line of the same screen.

The items displayed in the DSP1, DSP2, DSP3, and DSP4 screens are also used in the corresponding Stakeout
screens (SO2, SO3, SO4, and SO5).

You can also customize the displayed items in Stakeout.

Header characters

The following header characters can be used in DSP screens:

•

A colon (:) indicates that tilt correction is applied to the value.

•

A hash symbol (#) indicates that tilt correction is off.

•

An underscore (_) under the tilt correction character indicates that Sea
Level Correction or Scale factor is applied.

When the cursor is in a height (HT) field, only numeric input mode is available. Pressing

[MODE]

has no effect

when the cursor is in a HT field.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды