Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 181 / 185

background image

Total Station DTM-322 Instruction Manual

167

Error Messages

10

Recording Data

DATA FULL

100.19

The data storage is full.

Press any key to return to the Basic Measurement Screen (BMS). Then:

DUPLICATE PT

100.20

The input PT you are trying to record already exists in the current job. An existing
coordinate record cannot be overwritten by measured data.

Press any key to return to the point input screen. Change PT.

Duplicate PT

100.21

The input PT you are trying to record already exists in the current job as an SS, SO, or
CP record. An existing SS, SO, or CP record can be overwritten by measured data.

No Open Job

100.22

No job is open.

NO Stn Setup

100.23

There is no station record in the current job, or a station setup or BS check has not
been done since the program was rebooted.

To ...

Go to ...

delete unnecessary data

MENU > Data

delete jobs

MENU > Job

To ...

Press ...

return to the PT input screen

[ESC]

or the

Abrt

softkey

record RAW data and update XYZ data

the

XYZ

softkey

record RAW data only

the

RAW

softkey

To ...

Press ...

open the job list, if there are existing jobs

[1]

or select

Select job

create a new job

[2]

or select

Create job

return to the previous screen

[ESC]

To ...

Press ...

continue recording

[1]

or select

Continue

. If there is already an ST record in the

job, the message

CO, Use current orientation

appears.

go to the Stn Setup menu

[2]

or select

STN Setup

return to the previous screen

[ESC]

«
...
179
180
181
182
183
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: Omega Страницы: 24

FLEXFLO M4 Series

Бренд: Blue-White Страницы: 64

Бренд: LaserLiner Страницы: 52

Бренд: SIGRIST Страницы: 84

Alyza IQ PO4-XYZ

Бренд: Xylem Страницы: 172

350 Maritime V2

Бренд: TESTO Страницы: 106

Concert Monochord

Бренд: FEELTONE Страницы: 8

Бренд: Duratool Страницы: 4

BAE LX-XO-PL018-L S4 Series

Бренд: Balluff Страницы: 2

Бренд: Apera Страницы: 2

Mini-SuperGraph II

Бренд: NOMIS Seismographs Страницы: 44

Бренд: LaserLine Страницы: 11

Бренд: 3nh Страницы: 32

AquaInform Sycon 2500

Бренд: WACON Страницы: 52

Бренд: Modern Water Страницы: 17

Бренд: Velleman Страницы: 13

Бренд: Autometers Systems Страницы: 20

Бренд: Roli Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды