Nikon HQA46480 Скачать руководство пользователя

Страница: 164 / 185

Communications

150

Total Station DTM-322 Instruction Manual

Uploading Point Lists and Code Lists

Settings

To configure the transmission speed and other settings,
go to

MENU > Settings > Comm

. For more

information, see

Communications, page 107

File format

PT lists and code lists use the same record format. Use the filenames POINT.LST for
a PT list, and CODE.LST for a code list.

Figure 9.1

Record format for PT lists and code lists

DEFAULT
{

String1 , Code1
Layer2
{

String2-1, Code2-1
String2-2, Code2-2

}
Layer3
{

Layer 3-1
{

String3-1-1, Code3-1-1
String3-1-2, Code3-1-2

}
String3-2, Code3-2
String3-3, Code3-3

}
String4, Code4
String5, Code5
String6, Code6
String7, Code7

}

The first line of the file must
contain the text “DEFAULT” in
capital letters.

Curly brackets { } group items
together under the preceding
line.

For example, Layer 3-1
contains String 3-1-1 and
String 3-1-2.

Layer 3 contains the five
items from Layer 3-1 to
String 3-3.

“String” represents characters
that are displayed on the
screen. “Code” represents
characters that are stored in
the database.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды