Nikon HQA46480 Скачать руководство пользователя | Manualshive

Страница: 136 / 185

background image

5

Menu Key

122

Total Station DTM-322 Instruction Manual

Editing an item in the point list or code list

Use

[^]

or

[v]

to highlight the item that you want to edit.

Then press the

Edit

softkey.

An editing screen appears. For points, the Edit Item
screen appears. It contains only the PT field. For codes,
the Edit Code screen appears, containing the CD field
and the REC field.

Edit the text shown and then press

[ENT]

.

A confirmation screen appears. Press

[ENT]

or the

Yes

softkey to accept the changes and update the list.

Edit code list

•

The Edit Code screen has two fields. The CD field contains the text that
appears in the list screen. The REC field is optional. It contains the text
that is stored in the job. If you leave the REC field blank, the value in the
CD field is used.

•

You can use the REC field to use familiar words or codes on the screen,
but store a numeric code in the job. For example, if you set the CD field to
MANHOLE and the REC field to 1155, the text MANHOLE appears on the
screen, but the code 1155 is stored.

If you press the

Edit

softkey when a layer name appears, only the Lyr field

appears. To save changes to the layer name, press

[ENT]

in the Lyr field.

«
...
134
135
136
137
138
...
»

Содержание HQA46480


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HQA46480

Бренд: 4iiii Страницы: 3

Бренд: WAGER Страницы: 36

Бренд: Raycus Страницы: 40

Бренд: RaycoWylie Страницы: 31

Бренд: Sabre Страницы: 13

Бренд: AccuMac Страницы: 10

Бренд: Velleman Страницы: 107

Бренд: FMS Страницы: 12

BUCKMASTERS 1500

Бренд: Sig Sauer Страницы: 2

Бренд: RHS Страницы: 8

Litemaster Pro L-478DR

Бренд: Sekonic Страницы: 16

Бренд: Harken Страницы: 2

Бренд: Huvitz Страницы: 58

Бренд: Liquid Controls Страницы: 16

CHEM2000-UV-VIS

Бренд: Ocean Optics Страницы: 42

DUAL-BLEND 4114

Бренд: NCL Страницы: 7

Бренд: Bamo Страницы: 16

WaveRunner 8000-R

Бренд: Teledyne Lecroy Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды