Nikon HQA46480 Скачать руководство пользователя

Страница: 106 / 185

Menu Key

Total Station DTM-322 Instruction Manual

Cogo

Use the Cogo menu to perform coordinate geometry
(COGO) calculations. You can access this menu at any
time from any observation or PT input screen.

To open the Cogo menu, press

[2]

or select

Cogo

on the

MENU screen.

Calculating angle and distance between two coordinates

To open the Inverse menu, press

[1]

or select

Inverse

in the Cogo menu.

PT-PT inverse

PT-PT calculates the distance and the angle between two input points.

To calculate a PT-PT inverse:

Press

[1]

or select

PT-PT

in the Inverse menu.

Enter the first point number or name. Press

[ENT]

Type the second point number/name and press

[ENT]

. The

MSR

softkey allows you to shoot the

point on the spot to use it in the calculation.

The azimuth, horizontal distance, and vertical
distance from the first point to the second point
appear.

If you press

[ENT]

without entering a point name, a coordinate input screen appears, and you can enter

coordinates. These coordinates are not stored to the database. If you want to store the point, specify a new
point name.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды