THE 5560-CHGR10
WARNINGS
y
WARNING: For use only outside of hazardous locations.
IMPORTANT SAFETY INSTRUCTIONS
y
For personal safety, always confirm the rating of any known hazardous or
potentially hazardous location where the charger is to be used.
y
This product has a 3 prong polarized plug on the power cord. Do not
attempt to bypass this safety feature by removing the round plug and defeat
his safety feature. This plug will fit into a grounded outlet only one way. If
the plug does not fit fully into the outlet, contact a qualified electrician. Never
use with a two wire extension cord.
CAUTION
y
DO NOT use this charger in explosive atmospheres, near flammable
liquids, or where explosion proof lamps are required.
y
DO NOT use in the proximity of vehicles or equipment when there is a risk
of flammable liquids coming into contact with the charger
y
DO NOT immerse in water
y
DO NOT use in areas where water can accumulate or in rain or mist
y
CAUTION: Risk of Electric Shock – For Light Duty Dry Location Use Only
WARNING: NOT FOR USE IN HAZARDOUS LOCATIONS
ELECTRICAL CHARACTERISTICS
y
AC Input: 100-240Vac 50/60 Hz, 3A
y
DC Output: 5.5Vdc, 0.5A
MOUNTING THE CHARGER
WARNING: While the XPR-5560 Cap Lamp is certified as an Intrinsically
Safe Permissible product, the charger is NOT Intrinsically Safe. The
charger MUST be installed in a location far enough outside of the
hazardous environment to ensure that it can never come in contact with
any potentially explosive materials.
The Nightstick 5560-CHGR10 bank charger is designed to mount to any
flat, dry surface however special mounting requirements may require different
hardware. 1/2” lag bolts, masonry bolts, or wood screws are recommended to
mount the charger depending on what type of surface you are mounting to.
y
Select a location to install the charger making sure to check what is on
the other side of the mounting surface…no electrical wires, water lines, etc.
y
The other consideration for determining the mounting location of the
charger is the distance to the AC wall outlet or the 12v DC power outlet.
Please check to make sure that the cord will reach the charger when it
is plugged in. Otherwise, relocate the charger’s installation location as
needed.
y
Once the charger has been mounted, plug the cord into the power outlet.
y
The charger is now ready to use.
PLACING THE CAP LAMP INTO THE CHARGER
The Nightstick 5560-CHGR10 charger is designed to securely hold 10
properly installed XPR-5560G Cap Lamps in place.
y
Face the bezel portion of the Cap Lamp downward and push the
rectangular end of the Cap Lamp into the individual charging ports until the
light snaps securely into place.
y
When the 5560 is properly seated in the charger, the LED Charge Indicator
light will turn solid RED indicating that the Lithium-ion Rechargeable Battery
is charging. The Lithium-ion Rechargeable Battery is fully charged when the
LED Charge Indicator light turns GREEN.
REMOVING THE CAP LAMP FROM THE CHARGER
y
While positioned in front of the charger, grasp the Cap Lamp around the
bezel and gently pull on the light until it snaps out of the charging port.
y
The light has now been safely removed from the charger and is ready to
use.
BAYCO PRODUCTS LIMITED LIFETIME WARRANTY
WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in
workmanship and materials for the original purchaser’s lifetime. The Limited
Lifetime Warranty includes the LEDs, housing and lenses. Rechargeable
batteries, chargers, switches, electronics and included accessories are
warranted for a period of two years with proof of purchase. Disposable, non-
rechargeable batteries are excluded from this warranty. Normal wear and
failures which are caused by accidents, misuse, abuse, faulty installation and
lightning damage are also excluded.
In the event that Bayco Products, Inc. receives notice that any product
does not conform to its warranty, the original purchaser’s sole and exclusive
remedy, and Bayco Products, Inc.’s sole and exclusive liability, shall be
for Bayco Products, Inc., at its sole option, to either repair or replace the
non-conforming product in accordance with this limited warranty. The
original purchaser shall follow the instructions below to qualify for a repair
or replacement product. This is the only warranty, expressed or implied,
including any warranty of merchantability or fitness for a particular purpose.
IN NO EVENT WILL BAYCO PRODUCTS, INC. OR ITS AFFILIATES
OR SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY KIND REGARDLESS OF
THE FORM OF ACTION, WHETHER IN CONTRACT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY OR OTHERWISE. THE TOTAL
CUMULATIVE LIABILITY TO CUSTOMER, FROM ALL CAUSES OF
ACTION AND ALL THEORIES OF LIABILITY, WILL BE LIMITED TO AND
WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT PAID BY
CUSTOMER.
If this product is used for rental purposes, the warranty term is reduced to
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.mynightstick.com
INS-5560-CHGR10-17
Instruction Manual
5560-CHGR10
THANK YOU FOR SELECTING THE NIGHTSTICK 5560-CHGR10 BANK
CHARGER FOR THE XPR-5560G!
PLEASE SAVE THESE INSTRUCTIONS
Please read these instructions before using your Nightstick 5560-
CHGR10 Bank Charger. They include important safety information and
operating instructions.
BrightGuy.com is an authorized Nightstick distributor
